# Do products made from recycled plastic with additives fail early outdoors?

> **Summary:** The only direct test of a rigid bottle with this additive, run to recyclers' own protocol, found no early failure and no loss of strength outdoors.
> **Author:** Matthew
> **Published:** November 13, 2026
> **Canonical URL:** https://blog.gogreenfrog.com/do-products-made-from-recycled-plastic-with-additives-fail-early-outdoors

Here is the worry, and it is a fair one. You hear that a bottle made with "smarter" plastic will quietly fall apart. Crack on a sunny windowsill. Weaken on a garden shelf before you have finished what is inside. If you store supplements for months, that matters. So let us answer the actual question, plainly: there is no evidence that a rigid bottle made with recycled plastic and this additive fails early outdoors, and the only direct test of such a bottle found zero loss of strength.

## Where the scary story actually comes from

Almost every alarming claim about additive plastics "falling apart" traces back to studies of thin shopping bags and film, not bottles. That distinction is not a technicality. It is physics.

The additive used here works through oxygen reaching the plastic. A shopping bag is about 25 microns thin, so oxygen gets everywhere fast. A bottle wall is many times thicker, so oxygen barely penetrates the body of it. A 1982 study by Cunliffe and Davis established this decades ago: the thicker the plastic, the slower this kind of change happens. Borrowing a result from a carrier bag and pasting it onto a bottle overstates the risk, badly.

And until recently, nobody had actually tested a bottle. The worry was all inference. That changed in 2023.

## What happened when someone finally tested the bottle

![A woman holds a supplement bottle outdoors showing the BioBottles badge seal, sunlit forest trail in background](https://blog.gogreenfrog.com/rails/active_storage/representations/proxy/eyJfcmFpbHMiOnsiZGF0YSI6MTMzMCwicHVyIjoiYmxvYl9pZCJ9fQ==--bbe125058c547fdd1645799cacbad31370c0fc14/eyJfcmFpbHMiOnsiZGF0YSI6eyJmb3JtYXQiOiJqcGciLCJyZXNpemVfdG9fbGltaXQiOlsxMjAwLDEyMDBdLCJzYXZlciI6eyJxdWFsaXR5Ijo4NX19LCJwdXIiOiJ2YXJpYXRpb24ifX0=--2393484ad9276458d2809637f0976dfa36da19ca/badge-seal-on-supplement-bottle-outdoor-close-up.png)

A third-party laboratory, AIMPLAS, ran an actual rigid bottle made with this technology through the Association of Plastic Recyclers' Critical Guidance Protocol. The Association of Plastic Recyclers is the United States recycling industry's own body, and this is the exact test real recyclers use to judge whether a new package belongs in their stream.

The lab shredded the bottle, washed it, melted it, and blended it into ordinary recycled plastic at 25% and 50%, then measured strength, stiffness, and how it processed. These are the same steps a recycler performs.

Here is the result that answers the whole question.

| Property (50% blend) | Bottle with additive | Control, no additive |
| --- | --- | --- |
| Tensile strength | 27.6 MPa | 27.6 MPa |
| Pelletizing behaviour | All samples, including the control, showed low melt strength and strand breakage during pelletizing — a property of the material and the lab line, not of the additive. The report records this as 'Low melt-strength' for all three blends. | Same as bottle with additive |
| Flotation in wash | 100% | 100% |

A difference of zero on tensile strength. The strength of the material with the additive, even at half the blend, matched the plain plastic exactly. AIMPLAS reported no disconformities, with every property inside the recyclers' benchmarks.

## But what about actual sun and weather?

Fair follow-up. Strength in a lab is one thing. Years outdoors is another.

A separate third-party laboratory, Roediger, took recycled plastic containing up to 25% of this additive material and exposed it to the equivalent of more than two years of Southern-hemisphere sun. Its conclusion, in its own words: there is no evidence that adding up to 25% of this material "makes any difference to the outdoor life expectancy of a moulded product that has been exposed."

So the lab test and the weathering test point the same way. No early failure under realistic conditions.

## The honest limit, because you deserve it

There is one study where the additive did make a small difference, and skipping it would be dishonest. A weathering study by the laboratory TCKT looked at the deliberate worst case: thick outdoor sections made entirely from recycled additive-containing film, with no UV protection at all. It found slightly more surface cracking.

Read the detail, though. The unprotected plain plastic cracked too. And the same study found that the standard UV protection those outdoor products already contain erased the difference entirely. The report itself calls that scenario, 100% recycled film turned into thick outdoor lumber with no UV stabiliser, unlikely. It is not a supplement bottle on a shelf. In short, the only measurable effect appeared in a product that does not exist on your shelf, and it vanished the moment ordinary UV protection was present.

## So, do they fail early outdoors?

![Official BioBottles complete-system badge certifying bottle and cap](https://blog.gogreenfrog.com/rails/active_storage/representations/proxy/eyJfcmFpbHMiOnsiZGF0YSI6MTMwNSwicHVyIjoiYmxvYl9pZCJ9fQ==--8a3d64490ff49e4ab440f1d1c0bea0e7a8cdb433/eyJfcmFpbHMiOnsiZGF0YSI6eyJmb3JtYXQiOiJwbmciLCJyZXNpemVfdG9fbGltaXQiOlsxMjAwLDEyMDBdLCJzYXZlciI6eyJxdWFsaXR5Ijo4NX19LCJwdXIiOiJ2YXJpYXRpb24ifX0=--6f921b4698b039acba857128f38a20b8f4e53a00/biobottles-badge-complete-system.png)

No. Tested as a bottle, to the recyclers' own protocol, the material matched plain plastic for strength. Weathered for the equivalent of two years of sun, it made no difference to outdoor life expectancy. The one study that found any effect was a deliberate worst case that normal UV protection removed.

That is the real answer: a bottle built with [BioBottles® powered by PlasticIQ® technology](https://gogreenfrog.com) performs and stores like ordinary HDPE, and the testing that exists was run on the bottle itself, not borrowed from a bag.

The reports behind all of this are public at crm.gogreenfrog.com/evidence/, and samples are available at gogreenfrog.com.

What would it take to convince you: a test on the actual bottle, or an inference from a shopping bag?

## Sources

Reports and publications discussed in this article. Links lead to the report or its publisher; each finding applies to the materials and conditions tested.

- [AIMPLAS, APR Technology Validation of HDPE Rigid Containers, report AST-23-203-part1-EN/1, 4 December 2023.](https://crm.gogreenfrog.com/evidence/aimplas-apr-hdpe-validation-2023) (PDF)

- [Roediger Agencies cc, analytical laboratory report to Symphony Environmental Technologies PLC, 24 November 2010.](https://crm.gogreenfrog.com/evidence/roediger-d2w-recycling-2010) (PDF)

- [Burgstaller, C. & Reisecker, V., TCKT, 17 March 2016.](https://crm.gogreenfrog.com/evidence/tckt-mechanical-recycling-2016) (PDF)

- [Burgstaller, C. & Reisecker, V., TCKT, 27 July 2016.](https://crm.gogreenfrog.com/evidence/tckt-weathering-2016) (PDF)

## Sources

- [AIMPLAS, APR Technology Validation of HDPE Rigid Containers, report AST-23-203-part1-EN/1, 4 December 2023.](https://crm.gogreenfrog.com/evidence/aimplas-apr-hdpe-validation-2023)
- [Roediger Agencies cc, analytical laboratory report to Symphony Environmental Technologies PLC, 24 November 2010.](https://crm.gogreenfrog.com/evidence/roediger-d2w-recycling-2010)
- [Burgstaller, C. &amp; Reisecker, V., TCKT, 17 March 2016.](https://crm.gogreenfrog.com/evidence/tckt-mechanical-recycling-2016)
- [Burgstaller, C. &amp; Reisecker, V., TCKT, 27 July 2016.](https://crm.gogreenfrog.com/evidence/tckt-weathering-2016)

## Who makes BioBottles®?

BioBottles® and BioCaps® are made by GreenFrog Packaging®, the company that created the brand and owns the PlasticIQ® technology inside every bottle. They are manufactured in the USA. Brands buy direct from GreenFrog Packaging or through its authorized distributors.